1/9 august 2001 n high speed: t pd = 15 ns (typ.) at v cc =4.5v n low power dissipation: i cc =4 m a(max.) at t a =25 c n compatible with ttl outputs : v ih = 2v (min.) v il = 0.8v (max) n balanced propagation delays: t plh @ t phl n symmetrical output impedance: |i oh |=i ol = 6ma (min) n pin and function compatible with 74 series 241 description the 74hct241 is an advanced high-speed cmos octal bus buffer (3-state) fabricated with silicon gate c 2 mos technology. each control input governs four bus buffers. all inputs are equipped with protection circuits against static discharge and transient excess voltage. m74hct241 octal bus buffer with 3 state outputs (non inverted) pin connection and iec logic symbols order codes package tube t & r dip M74HCT241B1R sop m74hct241m1r m74hct241rm13tr tssop m74hct241ttr tssop dip sop
m74hct241 2/9 input and output equivalent circuit pin description truth table x : don't care z : high impedance absolute maximum ratings absolute maximum ratings are those values beyond which damage to the device may occur. functional operation under these conditions is not implied (*) 500mw at 65 c; derate to 300mw by 10mw/ c from 65 cto85 c recommended operating conditions pin no symbol name and function 1 1g output enable input 2, 4, 6, 8 1a1 to 1a4 data inputs 9, 7, 5, 3 2y1 to 2y4 data outputs 11, 13, 15, 17 2a1 to 2a4 data inputs 18, 16, 14, 12 1y1 to 1y4 data outputs 19 2g output enable input 10 gnd ground (0v) 20 v cc positive supply voltage inputs output inputs output 1g 1an 1yn 2g 2an 2yn lllhll l hhhhh hxz lxz symbol parameter value unit v cc supply voltage -0.5 to +7 v v i dc input voltage -0.5 to v cc + 0.5 v v o dc output voltage -0.5 to v cc + 0.5 v i ik dc input diode current 20 ma i ok dc output diode current 20 ma i o dc output current 35 ma i cc or i gnd dc v cc or ground current 70 ma p d power dissipation 500(*) mw t stg storage temperature -65 to +150 c t l lead temperature (10 sec) 300 c symbol parameter value unit v cc supply voltage 4.5 to 5.5 v v i input voltage 0 to v cc v v o output voltage 0 to v cc v t op operating temperature -55 to 125 c t r ,t f input rise and fall time (v cc = 4.5 to 5.5v) 0 to 500 ns
m74hct241 3/9 dc specifications ac electrical characteristics (c l = 50 pf, input t r =t f = 6ns) symbol parameter test condition value unit v cc (v) t a =25 c -40 to 85 c -55 to 125 c min. typ. max. min. max. min. max. v ih high level input voltage 4.5 to 5.5 2.0 2.0 2.0 v v il low level input voltage 4.5 to 5.5 0.8 0.8 0.8 v v oh high level output voltage 4.5 i o =-20 m a 4.4 4.5 4.4 4.4 v i o =-6.0 ma 4.18 4.31 4.13 4.10 v ol low level output voltage 4.5 i o =20 m a 0.0 0.1 0.1 0.1 v i o =6.0 ma 0.17 0.26 0.33 0.40 i i input leakage current 5.5 v i =v cc or gnd 0.1 1 1 m a i oz high impedance output leakage current 5.5 v i =v ih or v il v o =v cc or gnd 0.5 5 10 m a i cc quiescent supply current 5.5 v i =v cc or gnd 44080 m a d i cc additional worst case supply current 5.5 per input pin v i = 0.5v or v i = 2.4v other inputs at v cc or gnd 2.0 2.9 3.0 ma symbol parameter test condition value unit v cc (v) c l (pf) t a =25 c -40 to 85 c -55 to 125 c min. typ. max. min. max. min. max. t tlh t thl output transition time 4.5 50 7 12 15 18 ns t plh t phl propagation delay time 4.5 50 15 22 28 33 ns 4.5 150 21 30 38 45 t plh t phl propagation delay time 4.5 50 15 25 31 38 ns 4.5 150 21 33 41 50 t pzl t pzh output enable time 4.5 50 r l =1k w 17 30 38 45 ns 4.5 150 23 38 48 57 t plz t phz output disable time 4.5 50 r l =1k w 16 30 38 45 ns
m74hct241 4/9 capacitive characteristics 1) c pd is defined as the value of the ic's internal equivalent capacitance which is calculated from the operating current consumption without load. (refer to test circuit). average operating current can be obtained by the following equation. i cc(opr) =c pd xv cc xf in +i cc /8 (per circuit) test circuit c l = 50pf/150pf or equivalent (includes jig and probe capacitance) r 1 =1k w or equivalent r t =z out of pulse generator (typically 50 w ) symbol parameter test condition value unit v cc (v) t a =25 c -40 to 85 c -55 to 125 c min. typ. max. min. max. min. max. c in input capacitance 5101010pf c out output capacitance 10 pf c pd power dissipation capacitance (note 1) 31 pf test switch t plh ,t phl open t pzl ,t plz v cc t pzh ,t phz gnd
m74hct241 5/9 waveform 1 : propagation delay times (f=1mhz; 50% duty cycle) waveform 2 : output and enable times (f=1mhz; 50% duty cycle)
m74hct241 6/9 dim. mm. inch min. typ max. min. typ. max. a1 0.254 0.010 b 1.39 1.65 0.055 0.065 b 0.45 0.018 b1 0.25 0.010 d 25.4 1.000 e 8.5 0.335 e 2.54 0.100 e3 22.86 0.900 f 7.1 0.280 i 3.93 0.155 l 3.3 0.130 z 1.34 0.053 plastic dip-20 (0.25) mechanical data p001j
m74hct241 7/9 dim. mm. inch min. typ max. min. typ. max. a 2.65 0.104 a1 0.1 0.2 0.004 0.008 a2 2.45 0.096 b 0.35 0.49 0.014 0.019 b1 0.23 0.32 0.009 0.012 c 0.5 0.020 c1 45 (typ.) d 12.60 13.00 0.496 0.512 e 10.00 10.65 0.393 0.419 e 1.27 0.050 e3 11.43 0.450 f 7.40 7.60 0.291 0.300 l 0.50 1.27 0.020 0.050 m 0.75 0.029 s8 (max.) so-20 mechanical data po13l
m74hct241 8/9 dim. mm. inch min. typ max. min. typ. max. a 1.2 0.047 a1 0.05 0.15 0.002 0.004 0.006 a2 0.8 1 1.05 0.031 0.039 0.041 b 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 d 6.4 6.5 6.6 0.252 0.256 0.260 e 6.2 6.4 6.6 0.244 0.252 0.260 e1 4.3 4.4 4.48 0.169 0.173 0.176 e 0.65 bsc 0.0256 bsc k0 8 0 8 l 0.45 0.60 0.75 0.018 0.024 0.030 tssop20 mechanical data c e b a2 a e1 d 1 pin 1 identification a1 l k e 0087225c
m74hct241 information furnished is believed to be accurate and reliable. however, stmicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringe ment of patents or other righ ts of third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of stmicroelectronics. specifications mentioned in this pub lication are subject to change without notice. thi s pub lication supersedes and replaces all information previously supplied. stmicroelectronics prod ucts are not authori zed for use as critical components in life suppo rt devices or systems without express written approval of stmicroelectronics. ? the st logo is a registered trademark of stmicroelectronics ? 2001 stmicroelectronics - printed in italy - all rights reserved stmicroelectronics group of companies australia - brazil - china - finland - france - germany - hong kong - india - italy - japan - malaysia - malta - morocco singapore - spain - sweden - swit zerland - united kingdom ? http://w ww.st.com 9/9
|
